The Pentel GraphGear 1000 and GraphGear 500 share a 4 mm tip for drafting at a desk or on the move, and differ in how that tip is protected, in weight and in grip. Opening the 1000’s clip retracts the tip into the barrel, while the 500 keeps a fixed sleeve, so the 1000 is the pencil to carry and the 500 the one for the desk. The 1000 weighs 20 g to 20.6 g against 14.2 g to 15 g for the 500, and in North America only the 1000 has a lead hardness indicator, beside a finely chiseled metal grip with soft, latex-free pads where the 500 has a metallic mesh grip. Both sit among the best mechanical pencils for drafting, and the choice is between a protected tip on a metal barrel and a lighter, less expensive plastic body.
Pentel
Pentel was founded in 1946 as Dainippon Bungu Co., and it credits itself with two world firsts, the 1960 Hi-Polymer lead, the first mechanical-pencil lead made with synthetic resin in place of clay, and the 1968 Mechanica, the first 0.3 mm drafting mechanical pencil.
Pentel of America followed in 1965 and the Graph 1000 drafting pencil in 1986. The company took the name Pentel Co., Ltd. in 1971 and changed its corporate name to Astrum Co., Ltd. on April 1, 2026, and Pentel of America still sells both GraphGear pencils under the Pentel name.
What Is the Difference Between the GraphGear 500 and 1000?
The GraphGear 500 and 1000 part ways at the tip and in the barrel. The 1000’s 4 mm sleeve retracts via the clip, on a barrel that is metal outside and mostly plastic inside, while the 500’s 4 mm sleeve is fixed to a plastic body.
Both take the same Z2-1N eraser refill and both are made in Japan, but in Pentel’s US specifications the lead hardness indicator and the dual-action retractor belong to the GraphGear 1000 alone. The 500 comes pre-loaded with Super Hi-Polymer HB lead.
| Feature | GraphGear 1000 | GraphGear 500 |
|---|---|---|
| Tip | Retracts, rear knock to extend, clip to retract | Fixed, does not retract |
| Sleeve length | 4 mm | 4 mm |
| Barrel | Metal over a mostly plastic interior | Hexagonal plastic |
| Grip | Finely chiseled metal with soft, latex-free pads | Metallic mesh |
| Lead grade indicator | Rotating grade window | Not listed in North America, on the push button in Europe |
| Tip parts | Outer and inner tip | Single threaded tip, one piece with the grip |
| Lead sizes | 0.3, 0.5, 0.7 and 0.9 mm, plus 0.4 mm in Japan | 0.3, 0.5, 0.7 and 0.9 mm, plus 0.4 mm in Japan |
| Eraser refill | Z2-1N | Z2-1N |
| Origin | Japan | Japan |
Features as Pentel specifies them for the US, Japan, France, Germany and Canada, with the barrel row from hands-on teardowns. Descriptions of the 1000's barrel metal differ, so the row names no metal.
How Much Do the GraphGear 500 and 1000 Weigh?
Measured, the GraphGear 1000 weighs 20 g to 20.6 g and the GraphGear 500 14.2 g to 15 g, with one 0.3 mm 500 as light as about 11 g. Side by side on one scale, the 1000 comes out 5 grams heavier than the 500.
Pentel publishes no pencil weight for either model. For scale, a 1000 at 20.6 g sits just under a mostly brass Rotring 600 at 22.7 g on the same scale, and the Rotring line is weighed model by model in the three-way Rotring comparison.
| Measure | GraphGear 1000 | GraphGear 500 |
|---|---|---|
| Weight | 20.6 g or 0.73 oz on a 0.3 mm pencil, 20 g or 0.72 oz on a 0.5 mm | 14.2 g or 0.50 oz on a 0.3 mm pencil, 15 g or 0.53 oz on another |
| Length | 150 mm or 5.91 in, and 148.5 mm extended, 149 mm retracted on a 0.3 mm | 141 mm or 5.55 in on a 0.3 mm, 14 cm on another |
| Grip diameter | 9.5–10 mm across three samples | 9.2 mm and 9.6 mm on two pencils |
| Balance point | About 80 mm up from the tip, 79 mm from the sleeve end | 82.5 mm from the push button, at the end of the grip |
Every figure is a hands-on measurement of a single pencil. Pentel publishes no pencil weight for either model, and its shipping weights do not describe the pencil itself.
What Do the GraphGear Model Numbers Mean?
The model number names the lead size. A PG1015 is the 0.5 mm GraphGear 1000 in the US and in Japan, while the 0.5 mm GraphGear 500 is the PG525 in the US and the PG515 in Japan, and Pentel Japan adds a 0.4 mm size to both, the PG1014 and the PG514.
| Lead size | GraphGear 1000, US | GraphGear 1000, Japan | GraphGear 500, US | GraphGear 500, Japan and Europe |
|---|---|---|---|---|
| 0.3 mm | PG1013E | PG1013 | PG523E | PG513 |
| 0.4 mm | Not in the US list | PG1014 | Not in the US list | PG514, Japan only |
| 0.5 mm | PG1015A | PG1015 | PG525A | PG515 |
| 0.7 mm | PG1017C | PG1017 | PG527C | PG517 |
| 0.9 mm | PG1019G | PG1019 | PG529N | PG519 |
| Color | Accents in brown, black, blue and yellow from 0.3 to 0.9 mm in Canada | Silver barrel | Brown, black, blue and gray barrels from 0.3 to 0.9 mm | Silver barrel in Germany |
| Grade indicator | Yes | Yes | Not listed in the US or Canada | On the push button in France, an adjustable hardness indicator in Germany, none listed in Japan |
Model numbers for the US and Japan, with European numbers as Pentel Germany sells them. The 1000's accent colors follow its product names in Canada.
US numbers carry a letter, PG525A, where the German code is PG515-A. The European PG51x 500 has a different push button from the US PG52x and a barrel Pentel Germany calls silver and a German reviewer calls gray. In France that push button carries a grade indicator, in Germany the 500 has an adjustable lead hardness indicator, and in North America neither is listed for the PG52x.
Pentel Graphgear 1000 Drafting Pencil Review:
The Pentel Graphgear 1000 is the retractable model, sold in the US as the GraphGear 1000 Expert Mechanical Drafting Pencil in 0.3mm, 0.5mm, 0.7mm or 0.9mm, each size with its own barrel accent for easy identification: brown for 0.3 mm, black for 0.5 mm, blue for 0.7 mm and yellow for 0.9 mm. It pairs a finely chiseled metallic grip and soft, latex-free pads with a dual-action retractor that protects the tip and advances the lead, and it comes with Pentel Super Hi-Polymer lead, supplied as HB in France.
Product Features
1. Retractable Tip
On the Pentel GraphGear 1000, pressing the rear knock extends the tip, and opening the clip retracts the 4 mm sleeve fully. The stop is simple, as two teeth under the spring-loaded clip drop into the body when the tip is out and hold it there while writing. With the tip retracted, the pencil protects both its lead and the pockets or cases it travels in.
2. Metal Body
Pentel describes a sophisticated all-metal body, but hands-on teardowns find a metal exterior over a mostly plastic interior, and that plastic core keeps the weight down. The metal itself is disputed: Pentel Germany specifies stainless steel, one review describes the main section as aluminum tube, and a magnet test points to steel or stainless steel.
3. Well-Balanced And Comfortable Grip
At 20 g to 20.6 g the 1000 is the heavier of the pair, and it balances close to the middle of the barrel: about 80 mm up from the tip of a 150 mm pencil, or 79 mm from the sleeve end on a second sample.
The grip combines knurled metal with soft, latex-free pads of black rubber and measures 9.5 mm to 10 mm across. The pocket clip doubles as the retract trigger. On earlier pencils the clip’s fragile part was its leaf spring, which can break, and newer pencils carry a redesigned clip that pivots on a hinge or pin.
4. Lead Hardness Indicator
The built-in lead hardness indicator shows the loaded grade in a rotating window, and the grades it offers differ by market: HB, H, B and 2B on Japanese pencils, 2H, H, HB, B and 2B on US pencils. To change the grade setting, hold the grip, unscrew the outer tip, turn the grip to the grade and tighten the tip again. Forcing the grip round with the tip tightened can jam the tip or crack the hardness display section.
That plastic thread at the hardness display is the 1000’s known weak point. The plastic part near the display has broken on several pencils, and a recurring complaint is the pencil snapping where the plastic piece joins the body to the grip.
5. Price
The GraphGear 1000 costs more than the GraphGear 500 in both the US and Japan, and all four sizes of the 1000 are available in the US. Spare parts are sold too, including one replacement cap that fits both the 1000 and the 500, and the eraser refill is the Z2-1N.
Pros
- Tip that retracts via the clip
- Metal barrel with a knurled grip and latex-free pads
- Built-in lead hardness indicator
- 20 g to 20.6 g, measured
- Click mechanism that protects pockets and cases
Cons
- Plastic thread at the grade window that can crack
- Eraser that can come away with the cap, an occasional complaint
Pentel GraphGear 500 Mechanical Pencil Review:
The Pentel GraphGear 500 Mechanical Pencil is the fixed-sleeve model, with a weighted barrel, a sturdy 4mm tip, a metallic mesh grip and Super Hi-Polymer HB lead pre-loaded, in 0.3mm brown, 0.5mm black, 0.7mm blue or 0.9mm gray. The tip is one piece with the grip, so it does not loosen while writing, and the slim tip keeps the writing point visible. The mesh grip sits on a slim, beveled barrel, and the eraser refill is the Z2-1N.
Product Features
1. Lightweight
The 500 has a plastic body and weighs 14.2 g to 15 g measured, against 20 g to 20.6 g for the 1000. Pentel still sells it as weighted at the fingertips, and the pencil bears that out, with most of its weight close to the tip and the balance point at the end of the grip section.
2. Comes In Different Lead Thickness
The 500 comes in 0.3mm, 0.5mm, 0.7mm and 0.9mm in the US, and Japan adds the 0.4 mm PG514. The pre-loaded lead is Pentel Super Hi-Polymer HB, and Pentel credits its 1960 Hi-Polymer lead as the world’s first mechanical-pencil lead made with synthetic resin in place of clay. The 4mm tip is made for templates and rulers, and Pentel pitches the pencil for technical drawing and writing alike.
3. Fixed 4 mm Sleeve
The 500’s 4 mm sleeve is fixed and does not retract, and the push button only advances the lead, through a 3-jawed brass clutch that feeds almost 6 mm of lead in ten clicks on a measured sample. A bent guide pipe makes lead break more easily, and a metal tip can bend if the pencil is dropped.
4. Metal Grip
The metallic mesh grip is built for control and does not slip, and one review of the Pentel Graph Gear 500 identifies it as knurled steel that holds well even with sweaty or damp fingers. At 9.2 mm across on one pencil and 9.6 mm on another, it is close to the 1000’s 9.5 mm to 10 mm grip.
5. In-Built Eraser
The eraser sits under a cap that keeps it clean, and while it is very tiny it erases well. One replacement cap fits both the 500 and the 1000. After clearing a lead jam, refit the whole cap before testing the lead feed, because a bare eraser can be drawn into the lead tube.
6. Affordable Option
The GraphGear 500 is the budget choice of the two, less expensive in both the US and Japan, with a plastic body, a metal grip and sleeve and no retracting mechanism, and all four sizes are available in the US.
Pros
- Fixed 4 mm tip for templates and rulers
- 14.2 g to 15 g, measured
- Metallic mesh grip that holds with damp fingers
- Grade indicator on the push button of the European PG51x
Cons
- Sleeve that does not retract
- Very tiny eraser
- No grade indicator listed for the North American PG52x
Pentel Graphgear 1000 vs 500 FAQs
Pentel is a Japanese company. The names of its two pencils – GraphGear 500 and 1000 are kept in accordance with the price of these items in Japanese currency, Yen. The GraphGear 500 pencil costs 500 Yen, and the GraphGear 1000 model is priced at around 1000 Japanese Yen.
What Is the Difference Between the Graph 1000 For Pro and the GraphGear 1000?
The Graph 1000 For Pro is a separate Pentel pencil, the PG1003 to PG1009, with a black barrel, a matte black stepped tip, a hardness window, a metal-and-rubber grip and a low center of gravity. The GraphGear 1000 is the silver PG1013 to PG1019, whose tip retracts when the clip is opened. Inside, the For Pro pairs an aluminum grip section with a plastic body, where the GraphGear 1000 has a metal outer barrel, a knurled grip and a retractable lead pipe.
Where Does the GraphGear 300 Fit?
The GraphGear 300 sits in the same US range as the 500 and 1000, as the PG313 to PG319 in 0.3, 0.5, 0.7 and 0.9 mm, weighted for precision and balance, with a built-in textured metal grip and the Z2-1N eraser refill, and it is made in Japan.
Pentel Graphgear 1000 vs 500 Final Thoughts
Which is better depends on where the pencil lives. For one that travels in a pocket or a case, the GraphGear 1000 is the one to buy, because its retracting tip protects the lead, at the cost of about 5 grams more. At a desk with templates, the GraphGear 500’s fixed 4mm tip and lighter plastic body do the same work for less. Both are good pencils for technical drawing, and there the balance sets them apart: the 1000 balances about 80 mm up from the tip of a 150 mm pencil, while the 500 carries most of its weight closer to the tip. Other drafting pencils raise the same choice.
